Fass lift pump install instructions how to#
Fass lift pump install instructions install#
Fass lift pump install instructions manual#
Fass lift pump install instructions free#

Manner as before using all clips and securing devices provided by the manufacturer. Routing of fuel lines is especially important, so be sure to route fuel lines in the same

Reconnect all fuel lines and electrical connections securely ensuring that there are no kinks or perforations.

Fass lift pump install instructions install#

Once the fuel tank is in the correct position install the support straps and bolt in the same manner that they were removed.

Support the fuel tank in the correct installation position.

Replace any inferior or defective fuel lines or hoses.

Prior to lifting the fuel tank into place, ensure that all fuel lines and hoses sound.

It is imperative that pads are installed in the same manor that they were removed as missing or wrongly installed pads will cause noise or vibration to the vehicle.

As mentioned in section II, worn insulation and mounting pads must be replaced.

Reinstall the locking ring or retainer using the correct tools.

Fass lift pump install instructions free#

Be sure not to disturb the o-ring when seating the bracket while keeping the filter free of kinks and fold as this may restrict fuel flow. Carefully lower the bracket assembly into the fuel tank taking extra care not to bend or damage the float or the float arm.

Install a new o-ring (not included in the kit) in the groove at the bracket opening.

Ensure the bracket is fully assembled and ready for installation.

Clean out the fuel tank if necessary prior to bracket reinstallation. Before bracket reinstallation, carefully inspect the inside of the fuel tank for contamination, dirt or foreign matter.Ensure that all connections are secure before installation into the fuel tank.Replace the pump and filter as directed in the instructions that accompany the kit.

Discard the old o-ring seal it will be replaced with a new o-ring seal which is included in the kit. The old o-ring seal must be removed using extra care not to let pieces fall into the tank as it may be brittle.

Carefully lift out the bracket from the fuel tank.

Using the correct tools, remove the locking ring or retainer using care not to damage it.

This step must be done to prevent debris or foreign matter from entering the fuel tank which can cause problems later on.

Before removing the bracket from the fuel tank, be sure to thoroughly clean any dirt or debris that may have accumulated at the top of the fuel tank or at the opening of the locking ring area.

Worn or misaligned, wrongly installed pads should be replaced as they may affect the performance of the new fuel pump.

Take note of the condition and location of any insulating pads.

Take extra precautions to avoid a fuel spill.

Loosen the retaining straps of the fuel tank and support the fuel tank prior to removing the straps entirely.

If necessary, disconnect and remove the fuel filler neck from the vehicle.

Disconnect electrical connections at the fuel tank taking extra care not to damage pins or connectors.

Disconnect all visible fuel hoses that connect to the fuel tank from the rest of the vehicle (be sure to mark or label all connections for reassembly).

Visually inspect the scope of work involved before beginning the fuel tank removal step.

Fass lift pump install instructions manual#

For more specific instructions on fuel tank removal for your specific vehicle it may be necessary to obtain an approved Service Manual for the vehicle that you are replacing the fuel pump on. Fuel Tank RemovalР вЂќР вЂЎuel tanks vary from vehicle to vehicle the following fuel tank removal instructions are for a typical fuel tank removal. Take extra precautions to avoid gasoline spillage during the removal process. Once the vehicle is raised, additional gasoline can be removed through bracket connections.Р вЂќР вЂћTTENTION: Because of physical size and weight of vehicle fuel tanks, it is necessary to obtain help when removing the fuel tank from the vehicle.

Fuel tank gasoline levels will vary depending on the amount of gasoline removed through the filler neck.

Raise the vehicle with an automotive hoist or jack up the vehicle and support it with OSHA approved jack stands, which allow unobstructed clearance for the removal of the fuel tank.

Using only an OSHA approved gasoline transfer pump and approved fuel storage containers, remove as much gasoline as from the fuel tank through the filler neck.

Fass lift pump install instructions how to#

How to Install Electric Fuel Pump Drain the gasoline from the vehicleР Р†Р вЂљРІвЂћСћs fuel tank